Used Metal Forming Equipment & Presses for Sale
1 metal forming & presses lots at auction
Metal Forming Equipment & Presses by the numbers
From our own catalog: machines listed now and machines we have sold. Updated every few minutes.
Our track record
67 machines sold · 25 makes · model years 1972–2023 · 3 sold at our own auctions
By brand
| Brand | In stock now | Sold by Meadoworks | Model years |
|---|---|---|---|
| Cincinnati | 2 | 6 | 1991–1996 |
| Amada | 2 | 0 | 2022 |
| Pines | 2 | 0 | 2007 |
| Minster | 1 | 12 | 1972–2000 |
| Lawton | 1 | 2 | 1994 |
| Pacific | 1 | 2 | 1990 |
| Dener | 1 | 1 | 2023 |
| Knudson Manufacturing | 1 | 1 | 2002 |
| American Hercules | 1 | 0 | — |
| Carell | 1 | 0 | 2022 |
Looking for Something Specific?
Most of our inventory sells before we can list it online. If you need a specific brand, model, or specification, tell us what you need—we have access to unlisted equipment and machines coming in from plant closures.
Looking to Sell?
Meadoworks is an active cash buyer of used industrial equipment. Get a free valuation from our AMEA-certified appraisers.
About Used Metal Forming Equipment & Presses
Metal forming shapes metal with force instead of cutting it away. A hydraulic press pushes a ram. A press brake bends sheet in a die. A plate roll curves plate into a cylinder. A shear cuts a straight edge. A stamping press, a gap-frame press and a straight-side press are different frames for different tools, and they are not the same buy. Coil lines and roll forming belong in the same broad shop and they are their own machines. The point of this overview is to separate those frames before you compare tonnage.
Tonnage is a nameplate, not a personality. A 100-ton gap press and a 100-ton straight-side press do not hold a die the same way. The gap press is open on three sides and will deflect. The straight-side press keeps the slide square. A press brake's tonnage is per foot of bend as much as it is a total, and the die opening changes it. A plate roll is rated by thickness and width at a yield strength, not by a press ton. Reading one number across these machines will pick the wrong iron.
What you bring to the inspection changes with the frame. On a press, look at the ram, the ways or gibs, and the hydraulics. On a brake, look at the ram parallelism, the backgauge and the tooling. Rolls need a check for a crown or a flat spot, and for a drive that slips. A shear is the blade gap and the hold-down. None of those checks transfer. A clean paint job transfers even less.
Used metal forming equipment usually leaves a shop as a set of frames that did different jobs. Match the frame to the part. A cylinder is a roll. A flange is a brake. A drawn shell is a press with a shut height that fits the die. A straight cut is a shear. Buying the largest tonnage in the auction does not give you the motion the part needs. Measure the bed, the stroke and the opening against the tool you already have, then read the tonnage.
How to Choose Used Metal Forming Equipment & Presses
Press Force, Stamping Rate, or a Brake
A hydraulic press is the forming and assembly tool: full force anywhere in the stroke, dwell if the job needs it, and a frame chosen for access or rigidity. A stamping press is the production hitter. It wants a die, a feed, and a rate, and it is the wrong purchase if you only need a few formed parts a day. A press brake is the sheet-flange machine. Bed length and tonnage follow the longest bend, not the weight of the plate.
Pick the family from the part you repeat. A bracket with one bend is a brake conversation. A drawn cup or a progressive strip is a stamping conversation. A bushing pressed into a housing, or a plate straightened, is a hydraulic press conversation. Opening all three groups and comparing paint color will not make the choice.
Coil, Roll Forming, and Plate Rolls
A coil line exists so something downstream never waits on a shear blank. Reels, straighteners, and feeds belong with that idea. A roll former then turns the strip into a long, constant profile, one cross-section for the whole length. A plate roll takes a single plate and bends it into a cylinder or a cone. The roll former does not replace the plate roll, and the plate roll does not slit coil.
If the product is a tank shell or a pipe section cut from plate, start with plate rolls. If the product is hundreds of feet of the same channel, start with roll forming and the coil line that feeds it. Width, thickness, and yield have to match that family, not a press tonnage chart.
By Class: Typical Used Price Ranges and Our Track Record
Hydraulic gap and four-post presses under 100 tons: about $5,000–$30,000.
Press brakes, 100–250 tons with a CNC backgauge: about $40,000–$150,000.
Straight side stamping presses, 200–400 tons: about $80,000–$300,000.
Plate rolls, sheet and light plate to heavy plate: about $10,000–$150,000.
What moves the price — tonnage or capacity, bed size and length, the control and backgauge, the tooling and dies that come with the machine, the clutch, brake and hydraulics, and safety guarding.
Typical range of sizes: press brakes 90–700 tons with 8–16 ft beds, mechanical stamping presses 20–400 tons, hydraulic presses 5–600 tons, plate rolls from 10 gauge sheet to heavy plate.
What has moved through Meadoworks in metal forming: Cincinnati CNC hydraulic press brakes from 90 to 187 tons, Komatsu gap presses from 49 to 275 tons, Minster and Bruderer high-speed presses, Neff hydraulic presses from 5 to 600 tons, Lawton up-acting presses, and Carell, Parmigiani and Cole-Tuve plate rolls.
These are typical used-market ranges, not a quote on any one machine. For a current figure on a specific machine, request a quote or call 800-323-0307.
What to Inspect on Used Metal Forming Equipment & Presses
Read the nameplate
Tonnage or capacity, bed size, stroke and the voltage, so you compare the frame you need and not just the number.
Check the frame and slide
Look for weld repairs, cracks at the corners of a gap frame and wear in the gibs or ways that lets the slide or ram rock.
Run the hydraulics or the clutch and brake
Watch for leaks, slow cycling and pressure drop on a hydraulic machine; on a mechanical press, listen to the clutch and check the brake stops the slide on time.
Test the control and backgauge
Cycle every axis on a press brake or shear and confirm the backgauge repeats; on a CNC press, check that the control powers up and holds its programs.
Confirm the guarding
Light curtains, two-hand controls and interlocks should be present and working, because bringing a press up to code adds cost.
List the tooling that comes with it
Dies, punches, top and bottom tooling and rolls are often worth as much as the machine, so get it in writing.
Related Equipment
- Hydraulic Presses
Gap, straight-side, up-acting, and 4-post forming presses
- Stamping Presses
Mechanical and servo presses for die work
- Press Brakes
Sheet flanges and boxes, filed under fabricating
Metal Forming Equipment & Presses Brands We've Sold
Cincinnati
CNC hydraulic press brakes, our most handled forming make.
Neff Press
Hydraulic gap and four-post presses from 5 to 600 tons.
Komatsu
Gap frame mechanical presses, single and double crank.
Minster
Straight side and high-speed stamping presses.
Bruderer
Pillar-type precision high-speed presses.
Lawton
Up-acting four-post hydraulic presses.
Amada
Press brakes and turret punches.
Eaton Leonard
CNC rotary-draw tube benders.
Common Applications
Frequently Asked Questions
Which metal forming family fits a flange, a cylinder, or a stamped part?
Match the shape before the brand. A flange or a box from sheet belongs on a press brake. A cylinder or cone from plate belongs on a plate roll. A die and a strip belong on a stamping press. A slow squeeze, a dwell, or a press fit belongs on a hydraulic press. Coil lines and roll formers are the other metal forming paths when metal arrives as coil or must leave as a long profile. This group is only the map.
Do press brakes belong in this metal forming overview?
Yes. Press brakes bend sheet, so they are metal forming even though the catalog files them under fabricating with lasers, shears, and turret punches. This overview includes them so a buyer comparing a brake with a hydraulic press or a stamping press can see all three in one place. The brake groups themselves cover bed length, tonnage, and whether the control is CNC. Start there when the part is a bend. Wait when you are still deciding which family the part belongs to.
Is a coil line metal forming equipment or just a feeder?
A coil line is metal forming support that often decides whether the press can run. Uncoiling, straightening, and feeding let a stamping press or a roll former work from strip instead of from hand-fed blanks. The line is not a substitute for the press. If you already own the press and you are starving it, shop the coil groups. If the whole cell is in one closure, match the reel, straightener, and feed width to that press.
How is roll forming different from a plate roll in metal forming?
Roll forming pulls coil through a row of stands and produces a long part with one cross-section. A plate roll bends one plate into a curve, usually a cylinder or a cone, and then stops. Thickness, width, and the number of stands matter on a roll former. Roll diameter, rolling width, and three-roll versus four-roll matter on a plate roll. In metal forming those are different families, and a similar name is not a reason to treat them as the same machine.
What should I open first if I only know the part?
Write down the shape, the material thickness, and how many you make in a shift. Then pick one family from this metal forming overview and ignore the others until that group fails the part. A few bends a day point to a brake. A round shell points to a plate roll. A die and a rate point to stamping. A squeeze, a straighten, or an assembly point to a hydraulic press. Continuous profiles point to roll forming. The family group is where tonnage and bed size start to matter.
Where do Meadoworks metal forming machines come from?
They come off plant floors through closures, consignments, and auctions, listed by family so a press does not sit in a pile with a plate roll. Read each listing for the capacity that family uses. You can inspect before you commit, and a heavy machine is rigged with the rest of the load. This metal forming group will not tell you the tonnage you need. It will tell you which family group makes that tonnage the right kind of number.
Metal forming & press auctions (1 lot on 1 upcoming sale)
Shop Used Metal Forming Equipment & Presses by Type
- Used Hydraulic 4-Post Presses (2)
2 in stock now from Lawton.
- Used Plate Rolls (2)
2 in stock now from Carell and Parmigiani.
- Used Press Brakes (9)
9 in stock now from Amada, Cincinnati and American Hercules. 10 sold through Meadoworks.
- Used Roll Formers (1)
1 in stock now from Knudson Manufacturing.
- Used Stamping Presses (4)
4 in stock now from Lawton, Minster and Verson. 48 sold through Meadoworks.
- Used Tube & Pipe Benders (3)
3 in stock now from Pines and Comac.
