Used Slitter Rewinders for Sale
See all 3 Converting & Laminating →
1 result
Looking for Something Specific?
Most of our inventory sells before we can list it online. If you need a specific brand, model, or specification, tell us what you need—we have access to unlisted equipment and machines coming in from plant closures.
Looking to Sell?
Meadoworks is an active cash buyer of used industrial equipment. Get a free valuation from our AMEA-certified appraisers.
About Used Slitter Rewinders
A slitter rewinder takes a wide parent roll of film, foil, paper or laminate, cuts it into narrower webs, and winds those webs onto fresh cores. The unwind holds the roll. Knives sit in the span after the unwind. Rewind shafts build the finished rolls. It is not a laminator, and it is not a sheeter. The cut is in the web.
Knife style is the process choice. Razor slitting suits thin film. Score slitting presses a blade into a hardened anvil roll and suits some papers and light laminates. Shear slitting runs a pair of blades like scissors and holds a cleaner edge on thicker or tougher webs. Holders have to reach the narrowest finished width you sell. Shafts have to match the core diameter you already use. A frame bored for a 3-inch core will not run a 6-inch core until the shafts change.
Tension keeps the slit from wandering and the finished roll from starring or telescoping. Unwind brakes, nips and rewind drives have to stay in range as the parent diameter falls. A dancer or a load cell is how the control sees that change. Sharp knives will not save a roll that is soft on one side because the brake faded. Face width and the largest parent diameter decide whether your roll fits the unwind at all. A short face is a different frame, not a setup change.
Differential rewind shafts matter when adjacent slits want different tension, which is common once the web has a coated lane or a thickness streak. Locked shafts are simpler and fine when every slit is the same film at the same width. Lay-on rolls press the building roll so air does not stay in the wrap. A missing rider is why a roll looks fat and then goes soft on the pallet.
A used slitter rewinder is judged on the knives, the shafts and the tension, not on the paint. Turn each rewind by hand and feel for a bend. Rock a knife holder and look for play. If you can run a short web, watch the edge for weave. Ask the real speed on your material, because a light-film drive and a heavy-laminate drive can share a frame and not share a motor. Write down core size, minimum slit width and maximum rewind diameter before the truck is booked. A dull bottom band on a shear set is a consumable. A scored drum is a repair.
How to Choose a Used Slitter Rewinder
Shear vs Razor on a Slitter Rewinder
Shear slitting uses a pair of rotating knives, like a scissors, and it suits thicker webs and many laminates. Razor slitting uses a blade in the web path and suits a lot of thin films. Score slitting presses the web against a hardened roll and suits materials that crush cleanly.
The wrong knife fuzzes the edge or dusts the slit. You can change blades more easily than you can change the whole slitting method the machine was built around. Read which method is on the frame before you compare widths.
How to Size a Slitter Rewinder
Size the parent width first, then the narrowest slit you must hold, then the rewind diameter. A machine that takes the parent roll and cannot wind your finished width is not a fit. Core size has to match the shafts.
Speed is the last number. A fast machine with dull knives or a tension zone you cannot set will scrap the roll at any speed. Confirm you have a place to stage parent rolls and finished coils. The slitter is small compared with the rolls around it. Leave the laminator for a bond, not a cut.
Slitter Rewinder Specs to Compare
| Spec | Why it matters |
|---|---|
| Parent width | The parent roll has to fit the unwind and the knives. A narrow machine cannot take a wider roll. |
| Slit width | The setup has to hold that width. A machine that only makes wide slits will not fill the order. |
| Knife style | The web decides the knife. The wrong method dusts the edge or leaves a fuzzy cut. |
| Rewind diameter | Rewind capacity sets how often you stop to change cores. Too small and the line never settles. |
| Core size | A shaft that does not take your core is a hardware change before the first roll is salable. |
| Tension zones | Each zone has to be set. One frozen brake lets the web walk and ruins the edge. |
Parent width
The parent roll has to fit the unwind and the knives. A narrow machine cannot take a wider roll.
Slit width
The setup has to hold that width. A machine that only makes wide slits will not fill the order.
Knife style
The web decides the knife. The wrong method dusts the edge or leaves a fuzzy cut.
Rewind diameter
Rewind capacity sets how often you stop to change cores. Too small and the line never settles.
Core size
A shaft that does not take your core is a hardware change before the first roll is salable.
Tension zones
Each zone has to be set. One frozen brake lets the web walk and ruins the edge.
What to Inspect on a Used Slitter Rewinder
Cut a short roll
Look at the edge. Dust, fuzz or a wavy cut means knives or tension, not a counter that still counts.
Identify the knife style
Confirm razor, score or shear, and that the style suits your web. The frame will not become the other method.
Inspect knife condition
Nicked shear knives and spent razor blades leave a bad edge on the first revolution.
Check shafts and cores
Shafts should take the cores you use, and they should run true. A bent shaft appears as a bouncing roll.
Set each tension zone
Unwind, slit section and rewind should each be adjustable. One locked brake will not run a web straight.
Measure parent width
Compare the unwind face with your parent roll. A roll that will not mount is the end of the discussion.
Watch the rewind build
The finished rolls should build evenly. A telescope or a soft edge is tension, not a cosmetic quirk.
Related Equipment
- Converting & Laminating
Mills and laminators beside the slitter
- Laminators
Bond the web before you narrow it
- Additional Equipment
The rest of the surrounding plant gear
Common Applications
Frequently Asked Questions
How do I size a slitter rewinder for slit width?
Start with the parent roll width the unwind must accept, then the narrowest finished width you have to hold, then the rewind diameter and the core. A machine that mounts the parent roll and cannot wind your sellable width is not a fit. Knife style has to suit the web, shear, razor or score, or the edge will be wrong at any width. Speed is the last number. Cores and shafts have to match. Leave room to stage the parent rolls, because the rolls take more floor than the machine.
What is the difference between shear and razor on a slitter rewinder?
Shear slitting pairs rotating knives and suits thicker webs and many laminates. Razor slitting puts a blade in the path and suits a lot of thin films. Score slitting crushes the web against a hardened roll. The material picks the method more than the brochure does. A machine built for one method is not a quick conversion to another. Dull or nicked knives of the right method still make a bad edge, so condition matters after the method is right. Read the frame before you compare speeds.
What should I inspect on a used slitter rewinder?
Run a short roll and look at the edge and the way the rewind builds. Dust, fuzz, a telescope or a soft side points at knives or tension. Confirm the knife style and whether the knives are nicked. Check shafts for runout and for the core size you use. Each tension zone should move when you ask it to. Measure the unwind against your parent roll. A counter that still counts does not prove a clean slit.
Can a slitter rewinder laminate two webs?
No. A slitter rewinder changes width. It unwinds, cuts and rewinds. Bonding two webs is a laminator, with a nip and either an adhesive or a molten curtain. Plants often put the laminator upstream and the slitter after it, which is why people shop them in one breath. They are still different machines. If the structure does not exist yet, you need the laminator group. If the structure exists and it is simply too wide, you are in the right place.
What rewind diameter should a slitter rewinder handle?
The largest finished roll you want on a core, plus a little room so you are not running the arms at their stop every time. Too small and you change cores constantly and never get a stable tension. Too much machine for a tiny coil is wasted floor, but it still has to take your parent roll on the unwind, which is often the larger of the two diameters. Match both ends. A rewind that builds a telescope is a tension problem, not proof that the diameter rating was wrong.
How does unwind tension work on a slitter rewinder?
The unwind has to let the parent roll out under control so the web arrives at the knives flat and at a steady tension. A brake or a drive does that, and it has to be adjustable as the parent roll gets smaller and lighter. The slit section and the rewind have their own zones. If only the unwind is set and the rewind is frozen, the finished rolls telescope or go soft. Check that each zone moves.
