Used Single Screw Plastic Extruders for Sale
All used plastic extruders & extrusion equipment (14) →
See all 14 Extruders & Extrusion Lines →
2 results
Single Screw Extruders by the numbers
From our own catalog: machines listed now and machines we have sold. Updated every few minutes.
Our track record
21 machines sold · 9 makes · model years 1997–2017 · 14 sold at our own auctions
By brand
| Brand | In stock now | Sold by Meadoworks | Model years |
|---|---|---|---|
| Milacron | 1 | 11 | 1999–2018 |
| Welex | 1 | 1 | 2017 |
| Wayne Yellowjacket | 0 | 3 | — |
Looking for Something Specific?
Most of our inventory sells before we can list it online. If you need a specific brand, model, or specification, tell us what you need—we have access to unlisted equipment and machines coming in from plant closures.
Browse Used Single Screw Extruders by Brand
Browse Used Single Screw Extruders by Country
Looking to Sell Your Single Screw Extruders?
Meadoworks is an active cash buyer of used industrial equipment. Get a free valuation from our AMEA-certified appraisers.
About Used Single Screw Extruders
Single screw extruders (also called single extruder screw machines or single screw extrusion machines) are the most common type of plastic extruder. These machines use a single rotating screw inside a heated barrel to melt, mix, and convey thermoplastic material through a die to create continuous profiles, sheets, films, pipes, and other shapes. Single screw plastic extruders are the workhorse of the plastics extrusion industry.
Key specifications include screw diameter (typically 1.5" to 12"+), L/D ratio (24:1 to 36:1), drive horsepower, and throughput rate. Longer L/D ratios provide better mixing and output for demanding applications. Barrier screw designs improve melting efficiency and output consistency.
Meadoworks stocks used single screw extruder machines from Davis-Standard, NRM, Gloucester, American Kuhne, Egan, Johnson, Sterling, Welex, and Crown. Whether you need a plastic screw extruder for general purpose or a specialized single screw plastic extruder for specific applications, contact us at 800-323-0307.
How to Choose a Used Single-Screw Extruder
Diameter and L/D
A single-screw extruder melts and pumps. Diameter sets the rate. L/D, often 24:1 to 36:1, sets how much mixing and melting length you have. A short L/D will not finish a resin that needs venting or heavy mixing. A long L/D with a worn screw will not either.
Horsepower and the gearbox have to turn that screw in your resin at your rate. A lab extruder and a production extruder can share a brand and not share a job. Read inches or millimeters, L/D, and hp together.
The screw is the process
Barrier screws, mixing pins, and a vent are the geometry. A general-purpose screw in a filled compound or a shear-sensitive resin is the wrong tool even when the barrel is the right size. Ask what the screw was cutting, and whether a spare screw is in the sale.
Downstream is not included. A puller, a tank, a die, and a winder are separate machines. An extruder without the die for your product is a melt pump.
By size: Typical Used Single-Screw Extruder Price Ranges
1.5–2.5 in screw: about $10,000–$35,000
3–4.5 in screw: about $25,000–$90,000
6 in screw and up: about $60,000–$200,000+
Screw diameter and L/D, drive horsepower (AC or DC), screw and barrel wear, the gearbox, heating and cooling zones, the control and the brand move the price. Davis-Standard and NRM extruders hold value well.
These are typical used-market ranges, not a quote on any machine. For a current figure on a specific machine, request a quote or call 800-323-0307.
Single-Screw Extruder Specs to Compare
| Spec | Typical range | Why it matters |
|---|---|---|
| Screw diameter (in) | About 1.5–8 in on production machines | Rate follows diameter. A 2.5-inch screw will not do an 8-inch job. |
| L/D | Often 24:1 to 36:1 | Melting and mixing length. Vented extruders need the length for the vent to work. |
| Drive (hp) | Has to turn the screw in your resin at the rpm you need. A tired gearbox will not make the nameplate hp. | |
| Vent | Needed for wet or gassy resin. A plugged vent is a barrel you should see before you buy. |
Screw diameter (in)
Typical range: About 1.5–8 in on production machines
Rate follows diameter. A 2.5-inch screw will not do an 8-inch job.
L/D
Typical range: Often 24:1 to 36:1
Melting and mixing length. Vented extruders need the length for the vent to work.
Drive (hp)
Has to turn the screw in your resin at the rpm you need. A tired gearbox will not make the nameplate hp.
Vent
Needed for wet or gassy resin. A plugged vent is a barrel you should see before you buy.
What to Inspect on a Used Single-Screw Extruder
Measure screw and barrel
Wear is thousands of an inch, not a feeling. Ask for the numbers or plan to pull the screw.
Turn the gearbox
Noise under load, metal in the oil, and a hot box are the failures.
Heat every zone
A dead zone or a thermocouple that lies will burn one section and leave another unmelted.
Name the product
Pipe, profile, sheet, and compounding want different screws and different downstream. The extruder alone is not the line.
Related Equipment
- Desiccant Dryers
Dry the resin before it reaches the screw
- Strand Pelletizers
Cut a strand line into pellets
More Extruders & Extrusion Lines types
Types of Extrusion
Common Applications
Frequently Asked Questions
What is a single screw extruder?
A single screw extruder uses one rotating screw inside a heated barrel to melt, convey, and pump thermoplastic material through a die. It's the most common type of plastic extruder, used for film, sheet, pipe, profile, wire coating, and general-purpose extrusion applications. Single screw extruders are simpler and less expensive than twin screw extruders.
How much does a used single screw extruder cost?
Used single screw plastic extruder prices range from $10,000-$30,000 for small machines (1.5-2.5" diameter) to $50,000-$200,000+ for large production extruders (4.5-8"+ diameter). Pricing depends on screw diameter, L/D ratio, drive HP, brand, and condition. Davis-Standard and NRM extruders hold value well. Request a quote on any listing or call 800-323-0307 for a current price.
What L/D ratio do I need for a single screw extruder?
Most single screw extruders run 24:1 to 30:1. Longer barrels (30:1 to 36:1) help melting and venting, and vented two-stage screws are common for hygroscopic resins. Match the L/D and screw design to the resin and output you need.
What brands make single screw extruders?
Milacron is the single screw make Meadoworks has handled most, followed by Wayne Yellowjacket, Welex and NFM; we have also handled Genca and NRM extruders. Davis-Standard is also common on the used market.
What should I inspect on a used single screw extruder?
Measure screw and barrel wear (flight clearance), listen to the gearbox and check its oil, test every heater band and thermocouple, check the cooling fans or water, and run the drive under load. Ask what resin it last ran.
Related Resources
Recently Sold Single Screw Extruders
View all sold extrusion machines →Need Help Finding the Right Equipment?
Contact our team with your specifications and we'll help you find the right machine.





